WGB32B-PB
WGB32B
WGB32BM
WGB22B-PB
WDS150K
WF150K
What percentage of lead does this whole house system remove?This whole house system has an FCRC25B Lead removing filter. It reduces lead content up to below 15 ppb (parts per billion) which is the EPA (Environmental Protection Agency) standard for drinking water Will this home filtration system treat sulphur in my water?The contaminant that causes the rotten egg odor or sulfur odor in the water is Nitrate. This contaminant can be reduced by the Carbon block filter FC25B in the WGB32B-PB whole house water filtration system. If the sulfur smell is really strong in your water, we recommend installing our WF150K whole house central water filtration system. You can find it here. Canisters will not stop leaking what do I do?Most likely the o-ringsfor the canisters are not properly seated in the housing. If the problem persists after adjusting the orings, please give us a call at 678-261-7611 (M-F, 8:30 - 5:30 EST). We are happy to help! Will this home water filter replace a water conditionerNo. A water conditioner prevents scale build-up in your pipes and household appliances while this whole house filter will remove sediments, lead, taste, odors, and other contaminants from the water. How long does it take for water to start flowing through after initial installation?After turning on the water main to fill the housing, it may take a few minutes for the water to enter and saturate the whole house water filtration system. After the sound has stopped with water filling the system, you can open the cold water line and run the water to flush the filters. Will this whole house water filter remove chromium-6?This whole house water filtration system does not remove chromium. For removal of this contaminant we would recommend an under the sink RO System that utilizes an Reverse Osmosis membrane. You can find them here. Does home wate systems flow have to go right to left if you change the filter order accordingly?Normally the flow would be from right to left for this whole house water filter system but you can install in either direction. Just be sure to change the filter configuration based on how the system is installed and the water flow direction. Is there a website or somewhere it tells you which contaminants or chemicals each type filter takes out of the water?Please refer to the product listingson what contaminants each filter removes. Is necessary to install the UV filter along with the whole house water filter system?The UV filter is recommended if you have well water or other natural water sources. You can find it here Does this ispring home water filter system remove copper?WGB32B-PB whole house filter is rated to remove lead, but it does not remove copper. |
iSpring WGB32B-PB Whole House Water Filter System w/ 20'' x 4.5'' Sediment, Carbon, and Lead Reducing , 3-Stage Whole House Water Filtration System
-6%
$527.99
$560.99Triple the Savings, Triple the Joy!
About this item
- Protect your family from lead and more: WGB32B-PB whole house water filter is specially designed for reducing lead. Our 3rd stage FCRC25B lead removal filter features a high capacity of 150,000 gallons of water filtration at 100ppb for lead.
- DIY Installation and Maintenance: Refer to our manual and our helpful YouTube videos for easy DIY installation. With 1'' NPT inlet/outlet and 20'' x 4.5'' filter cartridges, this whole house water filter system has minimum impact on water flow (up to 15 GPM) and requires minimum maintenance.
- Top-notch quality - the first stage high capacity polypropylene sediment filter achieves filtration down to 5 microns. The second stage carbon block water filter is made of high quality coconut shell carbon for maximum filtration efficiency and filter life. Both whole house filters are tested by an independent third-party to meet NSF/ANSI standards. Both water filters have a capacity of 100,000 Gal. of water, enough to supply a family of four with clean water for a full year.
- Peace of mind customer service: Register online to activate your 1-year manufacturer warranty and lifetime free tech support from U.S. local team. We stand behind our products and if you encounter any problems please reach out to us. We are happy to help.
- Please note: Unlike an RO system, this whole house water filtration system will NOT reduce Total Dissolved Solids (TDS) and instead keeps healthy minerals in your water. If you are interested in a water filter that removes TDS consider our iSpring Reverse Osmosis systems. Each cartridge is individually wrapped to ensure that the filter stays fresh. Please unwrap the cartridges before installation.
Share
Frequently Bought Together
iSpring WGB32B-PB Whole House Water Filter System w/ 20'' x 4.5'' Sediment, Carbon, and Lead Reducing , 3-Stage Whole House Water Filtration System
$527.99
-6%
$560.99
$560.99
- Availability: In Stock
- Model: WGB32B-PB
- Manufacturer: iSpring
Write Review
michael s. | 
2017-08-09
Update: We still love it! We change the filters once a year! On our 3rd set and going great. We have had this filter installed now for about 5 months and we absolutely love it. I have a family of five and we live in a five bathroom home with 1 kitchen and a bar. We have well water on our homestead and we installed the 1 Inch Rusco / Vu-Flow 100 Mesh Spin Down Sediment Water Filter as directed in the instructions to help with filter maintenance. I did upgrade the filter cartridge in the 1 inch Rusco with the 200 mesh (74 mic) for 3/4 or 1" Spin-Down to handel Fine Sediment. This allows us to catch and wash away the larger particles in the water without clogging up the 5 micron 1st stage filter of the iSpring. We often have 2 showers going with a load of laundry and the dishwasher going. To this date we have not experienced a loss of water pressure. Our water is so much better now, it smells better, taste better and just looks cleaner. I feel good about letting this device treat the water for my family.
2017-08-09
Update: We still love it! We change the filters once a year! On our 3rd set and going great. We have had this filter installed now for about 5 months and we absolutely love it. I have a family of five and we live in a five bathroom home with 1 kitchen and a bar. We have well water on our homestead and we installed the 1 Inch Rusco / Vu-Flow 100 Mesh Spin Down Sediment Water Filter as directed in the instructions to help with filter maintenance. I did upgrade the filter cartridge in the 1 inch Rusco with the 200 mesh (74 mic) for 3/4 or 1" Spin-Down to handel Fine Sediment. This allows us to catch and wash away the larger particles in the water without clogging up the 5 micron 1st stage filter of the iSpring. We often have 2 showers going with a load of laundry and the dishwasher going. To this date we have not experienced a loss of water pressure. Our water is so much better now, it smells better, taste better and just looks cleaner. I feel good about letting this device treat the water for my family.
DEAN |
2019-08-05
This has worked well, water is now clear, but we are having an issue with slight leakage from sediment filter canister, where you screw in the canister there are fingers that stick down to center the filter, they cut into the filter causing pieces to tear off which interfere with a proper seal.
2019-08-05
This has worked well, water is now clear, but we are having an issue with slight leakage from sediment filter canister, where you screw in the canister there are fingers that stick down to center the filter, they cut into the filter causing pieces to tear off which interfere with a proper seal.
Mark D. |
2019-08-03
I am on well water. Installation was pretty much what I expected. I verified that the screws inside the metal head that hold the red buttons in place we’re not loose. I mounted the unit directly to the wall but didn’t like the way is sagged a bit (it’s heavy). So I drilled a couple of holes in the metal frame and added hooks, chains, and turnbuckles that I got from the hardware store. The turnbuckles allowed me to level the unit and support the weight evenly. I couldn’t decide whether to use shark bite fittings with compression rings or the slip fit style so I bought both and tried them both. I quickly decided that the slip fit was way better even though the cost was more. Not one single leak from the compression fittings and I had to remove and reinstall them a couple of times to get the routing the way I wanted (with the UV Sterilizer). I did have a couple of drips from the fittings that screw into to filter head on both sides but after adding more Teflon tape to the threads they stopped. It required about 6 turns of tape per fitting. I used an HQUA-OWS-124 UV filter, WSP-50 spin down filter, and Fleck 5600 SXT Softener to complete the system. After everything was up and running I noticed a glow in the Pex coming from both ends of the UV unit. I realized I should have used copper because the UV will deteriorate the Pex over time. It was easy to disassemble the routing because of the slip fit fittings. I simply cut copper tubing to match the same length and reinstalled since the fittings accepted Pex and copper both.
2019-08-03
I am on well water. Installation was pretty much what I expected. I verified that the screws inside the metal head that hold the red buttons in place we’re not loose. I mounted the unit directly to the wall but didn’t like the way is sagged a bit (it’s heavy). So I drilled a couple of holes in the metal frame and added hooks, chains, and turnbuckles that I got from the hardware store. The turnbuckles allowed me to level the unit and support the weight evenly. I couldn’t decide whether to use shark bite fittings with compression rings or the slip fit style so I bought both and tried them both. I quickly decided that the slip fit was way better even though the cost was more. Not one single leak from the compression fittings and I had to remove and reinstall them a couple of times to get the routing the way I wanted (with the UV Sterilizer). I did have a couple of drips from the fittings that screw into to filter head on both sides but after adding more Teflon tape to the threads they stopped. It required about 6 turns of tape per fitting. I used an HQUA-OWS-124 UV filter, WSP-50 spin down filter, and Fleck 5600 SXT Softener to complete the system. After everything was up and running I noticed a glow in the Pex coming from both ends of the UV unit. I realized I should have used copper because the UV will deteriorate the Pex over time. It was easy to disassemble the routing because of the slip fit fittings. I simply cut copper tubing to match the same length and reinstalled since the fittings accepted Pex and copper both.
Eric Troyer |
2018-03-28
Installed this in the pump house of my new home. Prior to instillation, the water smelled like sulfur and tasted awful. Now it’s odor free and I drink it straight from the tap. Since my well is new, the water had a lot of particulate matter. The filter does a nice job of removing it. I knew I wanted a filter since going to a lecture about the potential health risks of contaminants in well water. Not only from drinking it, but from bathing/showering in it. After researching different systems, I decided on this one The good reviews and reasonable pricing were the main reasons. 1year later, I am very satisfied with my decision. I combined this filter with a softener and uv filter and love the results.
2018-03-28
Installed this in the pump house of my new home. Prior to instillation, the water smelled like sulfur and tasted awful. Now it’s odor free and I drink it straight from the tap. Since my well is new, the water had a lot of particulate matter. The filter does a nice job of removing it. I knew I wanted a filter since going to a lecture about the potential health risks of contaminants in well water. Not only from drinking it, but from bathing/showering in it. After researching different systems, I decided on this one The good reviews and reasonable pricing were the main reasons. 1year later, I am very satisfied with my decision. I combined this filter with a softener and uv filter and love the results.
TexKan |
2020-05-21
This system is doing a great job on filtering from my well. PLAN your install, in a location that can get damp. When changing the filters, it is nearly impossible to get spin off the filters without getting some water spilled on the wall and floor. DO buy the WSP prefilter and install, as this allows you to easily relieve the pressure and greatly reduce the spilling of water. (I plumbed outside but drain to 5 gl bucket or a cooler will work fine also, if now drain is available.) The installation of shut off valves and by-pass to isolate the filters is a MUST! This not only reduces water spillage, but also avoids the introduction of much air into lines, so vritually no bleeding of air from the lines after a filter change. The Pre filter, also extends the life of your primary sediment filter and pays for itself in a couple of filter changes. Best $50 bucks spent in the entire bulid of our new home! Also if you are on a well, esp. a new or updated well, plan on a change of the sediment filter in first 30-45 days. I have a tankless water heate that was plugging up the filter screen every 4-7 days, after addition, has not plugged up once in last two months! The addition of the CTO barbon filter also removed what little taste was coming through to better than bottled water! Last, on my install I did not use the provided shut off valves, because I wanted a full inch line to the house, and while it shows it can install as 1 inch, it appeared to me and our plumber that it actually hooked to the 1" line, but actually reduced to 3/4", so we spent a few bucks for the 1" shut off. If you are running smaller than 1" line or not on a well, you will be fine with provided shut offs, and add the one additional to allow you to complete the bypass line! I have the install now for 60 days with no issues of any kind.
2020-05-21
This system is doing a great job on filtering from my well. PLAN your install, in a location that can get damp. When changing the filters, it is nearly impossible to get spin off the filters without getting some water spilled on the wall and floor. DO buy the WSP prefilter and install, as this allows you to easily relieve the pressure and greatly reduce the spilling of water. (I plumbed outside but drain to 5 gl bucket or a cooler will work fine also, if now drain is available.) The installation of shut off valves and by-pass to isolate the filters is a MUST! This not only reduces water spillage, but also avoids the introduction of much air into lines, so vritually no bleeding of air from the lines after a filter change. The Pre filter, also extends the life of your primary sediment filter and pays for itself in a couple of filter changes. Best $50 bucks spent in the entire bulid of our new home! Also if you are on a well, esp. a new or updated well, plan on a change of the sediment filter in first 30-45 days. I have a tankless water heate that was plugging up the filter screen every 4-7 days, after addition, has not plugged up once in last two months! The addition of the CTO barbon filter also removed what little taste was coming through to better than bottled water! Last, on my install I did not use the provided shut off valves, because I wanted a full inch line to the house, and while it shows it can install as 1 inch, it appeared to me and our plumber that it actually hooked to the 1" line, but actually reduced to 3/4", so we spent a few bucks for the 1" shut off. If you are running smaller than 1" line or not on a well, you will be fine with provided shut offs, and add the one additional to allow you to complete the bypass line! I have the install now for 60 days with no issues of any kind.
Doolin.Shea |
2018-03-02
I've only had the filter a couple of weeks but already can see improvement in the water quality. I'm on a well and have been drinking bottled water for years. Now I am able to drink the water from the tap.
2018-03-02
I've only had the filter a couple of weeks but already can see improvement in the water quality. I'm on a well and have been drinking bottled water for years. Now I am able to drink the water from the tap.
Joe |
2020-09-09
Hopefully this helps make everyone's life easier with finding the correct fittings. I used the paste sealer as another reviewer suggested and it leaked even when using a lot of paste. I used the paste on metal to metal without an issue but metal to plastic leaked. I ended up using Blue Monster thread seal tape and wrapping the fitting 10 times (possibly more) then running my nails through the treads to push it down a bit because the amount of tape. Worked perfectly the first time. Did the same for the sediment spin down filter.
2020-09-09
Hopefully this helps make everyone's life easier with finding the correct fittings. I used the paste sealer as another reviewer suggested and it leaked even when using a lot of paste. I used the paste on metal to metal without an issue but metal to plastic leaked. I ended up using Blue Monster thread seal tape and wrapping the fitting 10 times (possibly more) then running my nails through the treads to push it down a bit because the amount of tape. Worked perfectly the first time. Did the same for the sediment spin down filter.
RASHID007 |
2019-12-09
5 Years ago I bought a Reverse Osmosis system for my house. It worked perfectly for years. When the tap started to drip (I think my house has hard water which we've now solved) iSpring's customer service (Nick to be exact) went above and beyond. Rush shipped me replacement faucet after just a few minutes on the phone. Fast forward a few weeks and Customer Service was so good I ordered Whole House Filtration System, UV, Spindown, + another reverse Osmosis system for 2nd location in house. I know for a fact Customer Service will take care of me for years to come so I was confident spending thousands more on iSpring products. Whole House System one of the filters arrived damaged (from shipping company I'm sure) but iSpring as expected took care of it rush shipped out replacement filter at no cost. That's how you run a business, others can learn from iSpring. Oh and side note, water TDS went from 140 down to 9 so we have amazing water throughout whole house now!
2019-12-09
5 Years ago I bought a Reverse Osmosis system for my house. It worked perfectly for years. When the tap started to drip (I think my house has hard water which we've now solved) iSpring's customer service (Nick to be exact) went above and beyond. Rush shipped me replacement faucet after just a few minutes on the phone. Fast forward a few weeks and Customer Service was so good I ordered Whole House Filtration System, UV, Spindown, + another reverse Osmosis system for 2nd location in house. I know for a fact Customer Service will take care of me for years to come so I was confident spending thousands more on iSpring products. Whole House System one of the filters arrived damaged (from shipping company I'm sure) but iSpring as expected took care of it rush shipped out replacement filter at no cost. That's how you run a business, others can learn from iSpring. Oh and side note, water TDS went from 140 down to 9 so we have amazing water throughout whole house now!
john a salonia | 
2021-02-10
I'm writing this about 9 months after purchase because I had to change cartridges now. Well made product and simple to install. I had a plumber do the installation being I was having other work done in my home but could've done it myself. And customer service from I spring was outstanding. Don who called me to help me out was polite and more then helpful and an absolute gentlemen. Good company, good product and GREAT CUSTOMER SERVICE!
2021-02-10
I'm writing this about 9 months after purchase because I had to change cartridges now. Well made product and simple to install. I had a plumber do the installation being I was having other work done in my home but could've done it myself. And customer service from I spring was outstanding. Don who called me to help me out was polite and more then helpful and an absolute gentlemen. Good company, good product and GREAT CUSTOMER SERVICE!
iSpring FC25B High Capacity 20” x 4.5” Water Filter Replacement Cartridge - Carbon Block - Fits Standard 20” x 4.5” Whole House Water Filter Systems$61.99
iSpring RCC7AK, NSF Certified 75 GPD, Alkaline 6-Stage Reverse Osmosis System, pH Remineralization RO Water Filter System Under Sink, Superb Taste Drinking Water Filter$215.99
iSpring WGB32B Whole House Water Filter System, Highly Reduces Sediment, Taste, Odor, and up to 99% Chlorine, 3-Stage w/ 20-Inch Sediment and Carbon Block Filters, 1" Inlet/Outlet$485.99
iSpring FCRC25B 20” x 4.5” Water Filter Replacement Cartridge Lead Reducing$149.99
iSpring WGB22B-PB 2-Stage Whole House Water Filter System with 20" x 4.5" Sediment, Carbon, and Lead Reducing Water Filters$375.99
iSpring FP25B High Capacity 20” x 4.5” Whole House Water Filter Replacement Cartridge, Fine Sediment Filter, 5 Micron$32.99
iSpring WGB32BM Whole House Water Filter System, Reduces Iron, Manganese, Chlorine, Sediment, Taste, and Odor, 3-Stage Iron Filter Whole House$503.99
iSpring F3WGB32BPB 4.5” x 20” 3-Stage Whole House Water Filter Replacement Pack Set with Sediment, Carbon Block, and Lead Reducing Cartridges$200.99
iSpring WSP-SL Reusable Whole House Spin Down Sediment Water Filter Softener, Includes Siliphos Helps Prevent Scale and Corrosion, 1" MNPT 3/4" FNPT$67.99
iSpring WSP Reusable Whole House Spin Down Sediment Water Filter, 1" MNPT 3/4" FNPT w/Push to Connect Fittings, Lead-Free Brass$61.99
iSpring WGB32B-PB+AHPF12MNPT16X2 3-Stage Whole House Water Filtration System w/ 20” x 4.5” Fine Sediment, Carbon Block, Lead Reducing Filter, and 3/4'' Hose Connector$584.99
iSpring WGB22B-PB AHPF12MNPT16X2 2-Stage Whole House Water Filter System, Reduces Lead, Chlorine Home Water Filtration w/ 3/4'' Push-Fit Braided Stainless Steel Hose Connectors$485.99
LittleWell AHPF12MNPT16X2 12 inch Braided Stainless Steel Hose Connector with Ball Valve, 3/4 inch Push-Fit x 1 inch Male NPT, 2 Pack$83.99
iSpring RO500-BN NSF Certified Tankless RO Reverse Osmosis Water Filtration System, 500 GPD Fast Flow, Brushed Nickel Faucet, 2:1 Pure to Drain Ratio, White$563.99
iSpring WGB21B-PB 2-Stage Lead Reducing Whole House Water Filtration System w/ 10” x 4.5” Carbon Block Filter FC15B and Lead Reducing Filter FCRC15B$256.99
iSpring UVF55FS 55W Whole-House UV Water Filter With Smart Flow Sensor Switch, 120V, 12 GPM$289.99
iSpring WGB32B-KS Whole House Water Filter System, Reduces PFOA/PFOS, PFAS, Lead, Chlorine, Chloramine, Sediment, 3-Stage Whole House Water Filtration System$503.99
iSpring Whole-House UV Water Filter With Smart Flow Sensor Switch$307.99
- Start DownloadWGB32B-PB Manual.pdf
How to install
How to use
How to troubleshoot
Replacement Filters & Parts
Filters:
Fittings:
Pipes:
Warranty Registration & Help Center
Tell us about your shopping experience
