Ready to start your business? BECOME A DEALER

EARN UP TO 5% COMMISSION FOR EVERY SUCCESSFUL REFERRAL

iSpring WWC25 Whole House Well Water Chlorinator System

$1,099.99

About this item

Clean your Well Water: This heavy-duty and high capacity whole house well water chlorinator system automatically adds chlorine to your well water. According to the CDC, the benefits of chlorination are 1) Proven reduction of most bacteria and viruses in water; 2) Residual protection against recontamination; 3) Ease-of-use and acceptability; 4) Proven reduction of diarrheal disease incidence; 5) Scalability and low cost. In water, iron, manganese, and hydrogen sulfide can also be oxidized by chlorine, converting to precipitated material, which can then be removed by post-filtration.
A More Efficient and In-Control Chlorination Process Compared to the Systems with Tablets: This chlorinator system can achieve accurate chlorine residuals of 0.2 to 1.0 ppm in water. Coupled with an included pulse water meter, the dosing pump can inject the desired amount of chlorine according to the water flow measured by the pulse water meter. The chlorine residual level can be easily adjusted by using the UP and DOWN buttons on the dosing pump, depending on your water quality.
Less maintenance required: Instead of checking chlorine levels weekly, this well water chlorine system only requires making a new chlorine solution in the solution tank once every 1 to 3 months.
Sediment Filter & Test Kit Included: The included spin-down sediment filter takes out sand, rust, dirt, and various large sediment particles to increase the efficiency of chlorination, and extend the pump’s lifespan. The chlorine and pH test kit is also included to confirm the free-chlorine residual after water chlorination.
Recommendations: It is recommended that you get your well water tested by a qualified laboratory to understand the levels of various contaminants in your water before running this well water chlorinator. To remove the excessive chlorine in your water, we recommend installing a whole house carbon filter WGB32B at the point of entry. Other whole house water filters may also be necessary depending on the level of contaminants in your water. Please feel free to call us at 678-261-7611 (M- F, 8:30 – 5:30 EST) if you need a personalized product recommendation.
Optional Parts: You can add on the optional parts based on your preference and/or situation. For detailed information, please refer to the specifications below.
Chlorine is a strong oxidizing agent that can oxidize most reducing agents in water, such as hydrogen sulfide, iron, etc. Among these chemicals, the oxidized iron, to be mentioned, could turn the color of water into yellow due to its chemical property. To be noted that the chlorinator system can oxidize them but not remove them. For further removal, additional filtration processes may be needed. Please contact us for more information.
Note: This Whole House Well Water Chlorinator System is compatible with commercially available concentrated chlorine pellets.

iSpring WWC25 Whole House Well Water Chlorinator System

$1,099.99

High Accuracy

This chlorinator system can achieve accurate chlorine residuals of 0.2 to 1.0 ppm in water. Coupled with an included pulse water meter, the dosing pump can inject the desired amount of chlorine according to the water flow measured by the pulse water meter. The chlorine residual level can be easily adjusted by using the UP and DOWN buttons on the dosing pump, depending on your water quality.
Low Maintenance

Instead of checking chlorine levels weekly, this well water chlorine system only requires making a new chlorine solution in the solution tank once every 1 to 3 months.

Regular technical parameters

Minimum/Maximum feed water pressure = 35 - 100 psi
Minimum/Maximum feed water temperature = 39℉/4℃-100℉/38℃
Maximum filtered water flow: up to 22 GPM
Target free chlorine residual in product water: 0.2 to 1.0 ppm
Spin-down water filter supplied: WSP50

Installation Requirements

It is recommended to use 3/4'' CPVC pipe (not included in the package) to connect appropriate parts of the chlorinator, made in 3/4'' NPT. For example, the injection tee and pulse water meter should be connected with a 3/4'' CPVC pipe cut to the desired length, so are the check valve and sediment spin down filter. You can choose pipes with other sizes, but you will need proper fittings to change from 3/4'' NPT to your desired size.

Standard Parts

Dosing pump (6" L*4" W*7.5" H)

Max. capacity: 22 GPM
Max. pressure: 102 psi or 7 bars
Unit power: 20 watts
Max. temperature: 120°F or 50°C.
Coupled with the pulse water meter to inject the desired amount of chlorine into the incoming water.
The free chlorine residual level can be adjusted simply using the dosing pump's UP and DOWN arrow buttons.
For well water with bacteria, iron, manganese, hydrogen sulfide, please refer to the user manual for chlorine dose information.

25 Gallons PE Solution Tank

Maximum capacity: 25 gallons
Material: food-grade polyethylene (PE)
Diameter: 10 inches
Height: 33 inches
Color: white
Make a concentrated chlorine solution in the solution tank.
Translucent for easy viewing of fluid levels
Marked measurements (25, 50, 75, 100 Liter)

WSP50 can be replaced by WSP50ARB

Act as a pre-filter system to remove sediment, rust, dirt, sand, and large particles.
Help improve chlorination efficiency.
Refer to the WSP50 product description for more details: https://123filter.com/url/url.php?u=2e37536917.

Foot valve

The foot valve is designed to draw fluids upwards from the solution tank and into the dosing pump.
It also serves as a check valve to maintain the suction of fluids, preventing them from flowing downwards and back to the tank.

Chlorine and pH Test Kit

To test the free chlorine residual in your water following the chlorinator.

If you have an optional contact tank added to your chlorinator, you should sample the water after the contact tank but before any activated carbon filtration system.
If you have no contact tank, you can test the water at any point after the injection tee but before any activated carbon filtration system.

Refer to the instructions on the test kit for detailed information.

Injection Tee

The injection tee is the dosing point where chlorine enters the water supply line.
It also serves as a check valve that prevents the water in the supply line from back-flowing to the pump.
The injection tee needs to be cleaned 1 to 3 times a year, depending on use.

Suction Tubing

The suction tubing connects the foot valve on one end and the suction side of the pump on the other.
Dimension: 1/4 in. ID x 3/8 in. OD x 2.5 ft.
Material: clear PVC tubing (soft and transparent)

Air Exhaustion Tubing

The air exhaustion tubing connects the degassing port on the pump to the solution tank via the pre-drilled hole.
Dimension: 1/4 in. ID x 3/8 in. OD x 1.1 ft.
Material: clear PVC tubing (soft and transparent)

Discharge Tubing

The discharge tubing connects the pump discharge end and the injection tee.
Dimension: 1/4 in. ID x 3/8 in. OD x 6.5 ft.
Material: translucent PE tubing (stiff and translucent)

Ceramic Weight

The ceramic weight is placed on top of the foot valve to help it stand vertically at the bottom of the solution tank.

Pulse Water Meter (7" L*4" W*5" H)

Measure the water flow for the dosing pump to decide the amount of chlorine injection.
NSF 61 certified.
Can be installed horizontally or vertically.
Reed Switch: 1 pulse per gallon.
Min. and Max. Flow Rate: 0.5 to 22 GPM.
Lead-free.
Accuracy: /- 1.5% of maximum flow.

Optional Parts

T1054 Contact Tank (Optional)

Contact Tank

Pressure Tank Thread: 2 1/2″ NPSM
Pressure Tank Inlet/Outlet Connector: 3/4″ NPT
Type of the tank: pressure vessel
Diameter: 10 inches
Height: 54 inches
Max. capacity: 1.5 cubic feet or 16.38 gallons
Max. operating pressure: 150 psi/10 bar
Max. operating temperature: 120℉ or 50℃
It is recommended to install the optional contact tank after the chlorinator, so the chlorine and water have enough contact time to ensure the water is appropriately disinfected.
Fiberglass pressure vessels provide years of reliable service.

Cap for Contact Tank (with two connectors and two clips)

Install with the contact tank.

3/4'' NPT Push to Connect Straight Connector

Connect the contact tank to the CPVC pipe.
It is recommended to have this connector if you bought the contact tank.

AEPF12 3/4'' Push to Connect Elbow Fitting (Optional)

3/4'' push fitting, install as needed
The fastest way to connect PEX, copper, CPVC, PE-RT, and HDPE pipe
Push-to-connect fittings are ideal for installation in tight spaces.

WSP50ARB 50-micron Reusable Spin-down Water Filter with Automatic Flush (Optional)

The WSP50ARB can replace the WSP50 with an added automatic flush function. Refer to the WSP50ARB product description for more information.

ACVPF12 Check Valve (Optional)

The check valve only allows the flow of fluids in one direction.
The check valve can be installed at any site on the pipeline before the Pulse Water Valve.

APG2 Pressure Gauge (Optional)

The pressure gauge can be installed on the water line to measure the water pressure.

AFS6 Flow sensor switch (Optional)

Rated voltage: 120V AC
Max. current: 5A
Rated frequency: 60 Hz
Max. temperature: 131℉ or 55℃
The flow sensor switch measures the water flow that passes through it and sends signals to the pump.
It can replace the pulse water meter.
The flow sensor switch is turned on when the water flow rate is higher than 15-18 L/min, allowing water flow. When the water flow rate is less than this amount, the flow sensor switch is turned off and stops the water flow.